|
Cable Types |
Shielded and
unshielded Twisted Pair (STP, FTP, SSTP and UTP) LAN cabling:
|
|
Standard Link Interface Adapters
|
- TIA Category 3, 4, 5, 5E and 6: 100Ω
- ISO/IEC Class C and D: 100Ω and 120Ω
- ISO/ IEC Class E, 100W ISO/ IEC Class F, 100Ω
- Cat 6/ Class E permanent link adapters Plug type
and life: shielded and unshielded cable, TIA Cat 3, 4, 5, 5e, and 6 and
ISO/IEC Class C, D and E permanent link
- Cat 6/Class E channel adapters Plug type and
life: shielded and unshielded cable, TIA Cat 3, 4, 5, 5e, and 6 and ISO/IEC
Class C, D and E channels
|
|
Test Standards |
- TIA Category 3 and 5e per TIA/EIA-568B
- TIA Category 5 (1000BASE-T) per TIA TSB-95
- TIA Category 6 per TIA/EIA-568B.2-1
- TIA Category 6A per TIA/EIA-568B.2-10 (DTX-1800
only)
- TIA TSB-155 (DTX-1800 only)
- ISO/IEC 11801 Class C, D, and E
- ISO/IEC 11801 Class Ea, F (DTX-1800 only)
- EN 50173 Class C, D, E
- EN 50173 Class F (DTX-1800 only)
- ANSI TP-PMD
- IEEE 802.3 10BASE-T, 100BASE-TX, 1000BASE-T
- IEEE 802.3an 10GBASE-T
- IEEE 802.5 (STP cabling, IBM Type 1, 150Ω ) Token
Ring, 4 Mbps and 16 Mbps
|
|
Speed of Autotest |
Full 2-way Autotest of Category 6 Twisted-Pair links in 9 seconds or less
Full 2-way Autotest of ISO/IEC Class F links in 22 seconds |
|
Supported Tests Parameters
|
(The selected test
standard determines the test parameters and the frequency range of the
tests)
Wire Map
Length
Propagation Delay
Delay Skew
DC Loop Resistance
Insertion Loss (Attenuation)
Return Loss (RL), RL @ Remote
NEXT, NEXT @ Remote
Attenuation-to-crosstalk Ratio (ACR), ACR @ Remote
ELFEXT, ELFEXT @ Remote
Power Sum ELFEXT, PSELFEXT @ Remote
Power Sum NEXT, PSNEXT @ Remote
Power Sum ACR, PSACR @ Remote
|
|
Cable Tone Generator
|
Generates tones that can be detected by a tone probe such as a Fluke
Networks IntelliTone probe. The tones are generated on all pairs. Frequency
range on all pairs. Frequency range of tones: 440 Hz to 831 Hz |
|
Display |
3.7 in (9.4 cm)
diagonal, 240 dots wide by 320 dots high, passive color, transmissive LCD
with backlight. |
|
Input Protection
|
Protected against continuous telco voltages and 100 mA over-current.
Occasional ISDN over-voltages will not cause damage. |
|
Case |
High impact plastic
with shock absorbing overmold |
|
Dimensions |
Main unit and Smart Remote: 8.5 in x 4.4 in x 2.4 in (21.6 cm x 11.2 cm x
6cm), nominal |
|
Weight |
2.4 lb (1.1 kg),
nominal (without adapter or module) |
|
Operating Temperature
|
32°F to 104°F (0°C to 40°C) |
|
Storage Temperature
|
-4°F to 힍°F (-20°C to
°C) |
|
Operating relative humidity (% RH
without condensation) |
32°F to 95 °F (0°C to 35°C): 0 % to 90 % 95°F to 113°F (35°C to 45°C): 0 %
to 70 % |
|
Vibration |
Random, 2 g, 5 Hz
-500 Hz |
|
Shock |
1 m
drop test with and without module and adapter attached |
|
Safety |
CSA C22.2 No. 1010.1:
1992 EN 61010-1 1st Edition Amendments 1, 2 |
|
Pollution degree
|
Pollution Degree 2 as defined in IEC 60664 and applied to IEC 60950 "Safety
of Information Technology Equipment, 1999" |
|
Altitude |
Operating: 4000 m;
Storage: 12000 m |
|
EMC |
EN
61326-1 |
|
Power |
Main unit and remote:
Lithium-ion battery pack, 7.4 V, 4000 mAh
- Typical battery life: 12 to 14 hours
- Charge time (with tester off): 4 hours (below 40
°C)
- AC adapter/charger, USA version: Linear power
supply; Input 108 V ac to 132 V ac, 60 Hz ; Output 15 V dc, 1.2 A
- AC adapter/charger, international version:
Switching power supply; Input 90 V ac to 264 V ac, 48 to 62 Hz; Output
15 V dc, 1.2 A (isolated output)
- Memory backup power in main unit: Lithium battery
- Typical life of lithium battery: 5 years
- The battery will not charge at temperatures
outside of 0°C to 45°C (32°F to 113°F). The battery charges at a reduced
rate between 40°C and 45°C (104°F and 113°F).
|
|
Languages Supported |
English, French, German, Spanish, Portuguese, Italian,
Japanese, and Simplified Chinese |
|
Calibration |
Service center
calibration period is 1 year |
|
Performance Specifications |
Note: all specifications for tests on twisted-pair cabling apply to 100 Ω
cable. Contact Fluke Networks for information on measurement performance
for cable with a different impedance. |
|
Baseline accuracy |
The baseline accuracy
of all DTX Series testers meets or exceeds the requirements of Level IV as
in draft 2nd Edition of IEC 61935-1 over the frequency range supported by
the tester. |
|
Category 6/Class E link test modes
(and lower link categories) |
DTX
CableAnalyzer far exceeds Level III requirements of TIA/EIA-568-B.2-2 and
IEC 61935-1 |
|
Class F link test modes
|
DTX-1800 is compliant
with Level IV requirements as in the draft 2nd edition of IEC 61935-1.
|
|
Length for Twisted Pair Cabling
|
(Length specs do not include the uncertainty of the cable's NVP Value) |
|
Parameter |
Single-ended Test
Dual-ended Test (Main and Remote) |
|
Range |
800
m (2600 ft) - Single-ended Test
150 m (490 ft) - Dual-ended Test (Main and Remote) |
|
Resolution |
0.1 m or 1 ft -
Single-ended Test
0.1 m or 1 ft - Dual-ended Test (Main and Remote) |
|
Accuracy |
±
(1m 4%) - Single-ended Test
± (1m 4%) - Dual-ended Test (Main and Remote) |
|
Delay Skew |
|
Parameter |
Twisted Pair Cabling |
|
Range |
0
ns to 100 ns |
|
Resolution |
1 ns |
|
Accuracy |
±
10 ns |
|
DC Loop Resistance
Test |
|
Parameter |
Twisted Pair Cabling |
|
Range |
O Ω
to 53Ω |
|
Resolution |
0.1 Ω |
|
Accuracy |
±
(1 Ω 1%) |
|
Overload Recovery Time |
Less than 10 minutes
to rated accuracy following over-voltage. Referencing is required after
repeated or prolonged over-voltage. |
SHOPPING CART
