Net Prowler Cabling and Advanced Network Tester
|
The Net Prowler™ Cabling and Advanced Network Tester takes all the features and functionality of the Cable Prowler™ and adds the capability to identify, monitor, and troubleshoot LAN issues associated with physical layer and link conditions in the network.
- |
Identify, monitor, and correct LAN issues |
- |
Supports IPV4 and IPV6 protocols |
- |
Verifies DHCP connectivity and DNS |
- |
Pings IPV4, IPV6, and URL addresses |
- |
CDP, LLDP, NDP, and VLAN detection |
- |
TCP/UDP Throughput Test |
- |
Detects presence of PoE and class of PoE per IEEE 802.3af/at with load test for voltage drop |
- |
Detects and reports current link speed and link capabilities for active Ethernet drops up to 1 Gbps |
- |
Link light to identify location on a hub/switch/router port |
- |
Tests CAT3/5e/6/6a Ethernet cable configuration and verifies connectivity while conducting tests for opens, shorts, miswires, split pairs, and reverses |
- |
Supports up to 8 testing and ID remotes for network & telephone cables |
- |
Supports up to 20 network and coax ID-only mapping remotes |
- |
Ability to define Network test name, cable name, save and print all results (cable testing and network testing) |
|
|
Network Testing - PoE Testing |
- |
Detects and reports advertised and current link speed and link speed |
- |
Ping both IPV4 and IPV6 addresses |
- |
Detects the presence of VLANs |
- |
CDP/LLDP/ NDP and VLAN identifi cation provides network configuration information |
- |
Ping specifi c URL to verify WAN connectivity |
- |
Blinks link light to identify location on a hub/switch/router port |
- |
Detects presence of PoE and class of PoE per IEEE 802.3af/at with load test for voltage drop |
|
Physical Features |
- |
High resolution full color graphical display |
- |
Displays wire map in color per TIA-568A/B color codes, in pin or pair order (confi gurable) |
- |
Protective rubber boot |
- |
Micro USB connector (to export cable reports), RJ45 connector, and coax connector |
|
Net Prowler Application |
- |
Preview test results as PDF or CSV |
- |
Perform throughput test using the Net Prowler |
- |
Update Net Prowler Firmware |
|
|
Specifications
|
Measurement Technology
|
Time Domain Reflectometry (TDR) |
Cable Measurements
|
Cable Testing and ID: up to 1000 ft (305 m)
Split Pair Detection: 3 ft (1 m) to 1,000 ft (305 m)
Length Measurement: 0 to 1,500 ft (457 m), ± (5%+1ft)
Supports 8 continuity and ID number remotes (RJ-45)
Supports 20 RJ-45 and 20 F-connector ID only remotes |
Power over Ethernet
|
Tests for IEEE 802.3af and IEEE 802.3at (PoE Plus)
compliant PoE
Loads cable up to 25.5 watts
(at class 4) Identifies Mode A or B (pairs with PoE) |
Active Ethernet
|
Indicates advertised speeds of 10/100/1000base-t half or
full duplex
Can Link to network at 10/100base-t |
Maximum Voltage
|
Parameters refer to the maximum voltage that can be applied to any 2 connector pins without causing damage to the tester.
• RJ Jack: 66 Vdc or 55 Vac
• F-connector: 50 Vdc or Vac |
Save Test Results
|
Stores up to 250 Cable or network tests with user defined names |
Tone Generation
|
Tone Frequencies: 730 Hz and 1440 Hz |
Languages
|
English, French, Spanish, German, Italian |
Battery Life
|
For 6 x AA, 9VDC, 2,200 mA-hr (typical) alkaline battery:
Operating – 20 hours typical
Standby – Life of battery (20uA max)
Batteries are included |
Altitude
|
10,000 ft (3048 m) operating |
Temperature
|
Operating: 32 to 122°F (0 to 50°C)
Storage: -22 to +140°F (-30 to 60°C) |
Humidity
|
10 to 90% non-condensing |
Enclosure
|
High-strength PC/ABS plastic with V0 rating with boot
Withstands 4 foot drop on to concrete |
Size
|
1.85”H x 3.6”W x 6.8”L (4.7 x 9.15 x 17.3 cm) |
Safety Compliances
|
CE |
Weight with Batteries
|
1 lb 2 oz (510 g) |
Warranty
|
1 Year |
|
|
|
|
|
The Net Prowler™ Cabling and Advanced Network Tester takes all the features and functionality of the Cable Prowler™ and adds the capability to identify, monitor, and troubleshoot LAN issues associated with physical layer and link conditions in the network.
- |
Identify, monitor, and correct LAN issues |
- |
Supports IPV4 and IPV6 protocols |
- |
Verifies DHCP connectivity and DNS |
- |
Pings IPV4, IPV6, and URL addresses |
- |
CDP, LLDP, NDP, and VLAN detection |
- |
TCP/UDP Throughput Test |
- |
Detects presence of PoE and class of PoE per IEEE 802.3af/at with load test for voltage drop |
- |
Detects and reports current link speed and link capabilities for active Ethernet drops up to 1 Gbps |
- |
Link light to identify location on a hub/switch/router port |
- |
Tests CAT3/5e/6/6a Ethernet cable configuration and verifies connectivity while conducting tests for opens, shorts, miswires, split pairs, and reverses |
- |
Supports up to 8 testing and ID remotes for network & telephone cables |
- |
Supports up to 20 network and coax ID-only mapping remotes |
- |
Ability to define Network test name, cable name, save and print all results (cable testing and network testing) |
|
|
Network Testing - PoE Testing |
- |
Detects and reports advertised and current link speed and link speed |
- |
Ping both IPV4 and IPV6 addresses |
- |
Detects the presence of VLANs |
- |
CDP/LLDP/ NDP and VLAN identifi cation provides network configuration information |
- |
Ping specifi c URL to verify WAN connectivity |
- |
Blinks link light to identify location on a hub/switch/router port |
- |
Detects presence of PoE and class of PoE per IEEE 802.3af/at with load test for voltage drop |
|
Physical Features |
- |
High resolution full color graphical display |
- |
Displays wire map in color per TIA-568A/B color codes, in pin or pair order (confi gurable) |
- |
Protective rubber boot |
- |
Micro USB connector (to export cable reports), RJ45 connector, and coax connector |
|
Net Prowler Application |
- |
Preview test results as PDF or CSV |
- |
Perform throughput test using the Net Prowler |
- |
Update Net Prowler Firmware |
|
|
Specifications
|
Measurement Technology
|
Time Domain Reflectometry (TDR) |
Cable Measurements
|
Cable Testing and ID: up to 1000 ft (305 m)
Split Pair Detection: 3 ft (1 m) to 1,000 ft (305 m)
Length Measurement: 0 to 1,500 ft (457 m), ± (5%+1ft)
Supports 8 continuity and ID number remotes (RJ-45)
Supports 20 RJ-45 and 20 F-connector ID only remotes |
Power over Ethernet
|
Tests for IEEE 802.3af and IEEE 802.3at (PoE Plus)
compliant PoE
Loads cable up to 25.5 watts
(at class 4) Identifies Mode A or B (pairs with PoE) |
Active Ethernet
|
Indicates advertised speeds of 10/100/1000base-t half or
full duplex
Can Link to network at 10/100base-t |
Maximum Voltage
|
Parameters refer to the maximum voltage that can be applied to any 2 connector pins without causing damage to the tester.
• RJ Jack: 66 Vdc or 55 Vac
• F-connector: 50 Vdc or Vac |
Save Test Results
|
Stores up to 250 Cable or network tests with user defined names |
Tone Generation
|
Tone Frequencies: 730 Hz and 1440 Hz |
Languages
|
English, French, Spanish, German, Italian |
Battery Life
|
For 6 x AA, 9VDC, 2,200 mA-hr (typical) alkaline battery:
Operating – 20 hours typical
Standby – Life of battery (20uA max)
Batteries are included |
Altitude
|
10,000 ft (3048 m) operating |
Temperature
|
Operating: 32 to 122°F (0 to 50°C)
Storage: -22 to +140°F (-30 to 60°C) |
Humidity
|
10 to 90% non-condensing |
Enclosure
|
High-strength PC/ABS plastic with V0 rating with boot
Withstands 4 foot drop on to concrete |
Size
|
1.85”H x 3.6”W x 6.8”L (4.7 x 9.15 x 17.3 cm) |
Safety Compliances
|
CE |
Weight with Batteries
|
1 lb 2 oz (510 g) |
Warranty
|
1 Year |
|
|
|
|
|
The Net Prowler™ Cabling and Advanced Network Tester takes all the features and functionality of the Cable Prowler™ and adds the capability to identify, monitor, and troubleshoot LAN issues associated with physical layer and link conditions in the network.
- |
Identify, monitor, and correct LAN issues |
- |
Supports IPV4 and IPV6 protocols |
- |
Verifies DHCP connectivity and DNS |
- |
Pings IPV4, IPV6, and URL addresses |
- |
CDP, LLDP, NDP, and VLAN detection |
- |
TCP/UDP Throughput Test |
- |
Detects presence of PoE and class of PoE per IEEE 802.3af/at with load test for voltage drop |
- |
Detects and reports current link speed and link capabilities for active Ethernet drops up to 1 Gbps |
- |
Link light to identify location on a hub/switch/router port |
- |
Tests CAT3/5e/6/6a Ethernet cable configuration and verifies connectivity while conducting tests for opens, shorts, miswires, split pairs, and reverses |
- |
Supports up to 8 testing and ID remotes for network & telephone cables |
- |
Supports up to 20 network and coax ID-only mapping remotes |
- |
Ability to define Network test name, cable name, save and print all results (cable testing and network testing) |
|
|
Network Testing - PoE Testing |
- |
Detects and reports advertised and current link speed and link speed |
- |
Ping both IPV4 and IPV6 addresses |
- |
Detects the presence of VLANs |
- |
CDP/LLDP/ NDP and VLAN identifi cation provides network configuration information |
- |
Ping specifi c URL to verify WAN connectivity |
- |
Blinks link light to identify location on a hub/switch/router port |
- |
Detects presence of PoE and class of PoE per IEEE 802.3af/at with load test for voltage drop |
|
Physical Features |
- |
High resolution full color graphical display |
- |
Displays wire map in color per TIA-568A/B color codes, in pin or pair order (confi gurable) |
- |
Protective rubber boot |
- |
Micro USB connector (to export cable reports), RJ45 connector, and coax connector |
|
Net Prowler Application |
- |
Preview test results as PDF or CSV |
- |
Perform throughput test using the Net Prowler |
- |
Update Net Prowler Firmware |
|
|
Specifications
|
Measurement Technology
|
Time Domain Reflectometry (TDR) |
Cable Measurements
|
Cable Testing and ID: up to 1000 ft (305 m)
Split Pair Detection: 3 ft (1 m) to 1,000 ft (305 m)
Length Measurement: 0 to 1,500 ft (457 m), ± (5%+1ft)
Supports 8 continuity and ID number remotes (RJ-45)
Supports 20 RJ-45 and 20 F-connector ID only remotes |
Power over Ethernet
|
Tests for IEEE 802.3af and IEEE 802.3at (PoE Plus)
compliant PoE
Loads cable up to 25.5 watts
(at class 4) Identifies Mode A or B (pairs with PoE) |
Active Ethernet
|
Indicates advertised speeds of 10/100/1000base-t half or
full duplex
Can Link to network at 10/100base-t |
Maximum Voltage
|
Parameters refer to the maximum voltage that can be applied to any 2 connector pins without causing damage to the tester.
• RJ Jack: 66 Vdc or 55 Vac
• F-connector: 50 Vdc or Vac |
Save Test Results
|
Stores up to 250 Cable or network tests with user defined names |
Tone Generation
|
Tone Frequencies: 730 Hz and 1440 Hz |
Languages
|
English, French, Spanish, German, Italian |
Battery Life
|
For 6 x AA, 9VDC, 2,200 mA-hr (typical) alkaline battery:
Operating – 20 hours typical
Standby – Life of battery (20uA max)
Batteries are included |
Altitude
|
10,000 ft (3048 m) operating |
Temperature
|
Operating: 32 to 122°F (0 to 50°C)
Storage: -22 to +140°F (-30 to 60°C) |
Humidity
|
10 to 90% non-condensing |
Enclosure
|
High-strength PC/ABS plastic with V0 rating with boot
Withstands 4 foot drop on to concrete |
Size
|
1.85”H x 3.6”W x 6.8”L (4.7 x 9.15 x 17.3 cm) |
Safety Compliances
|
CE |
Weight with Batteries
|
1 lb 2 oz (510 g) |
Warranty
|
1 Year |
|
|
|
|
|