- Hex hole sizes: .350 in.(8.89mm), .3208 in.(8.13mm), and .255 in. (6.48mm)
- Provides good and consistent crimp every time
- Dies change quickly and easily with a screwdriver
- Interchangeable dies provide versatility in a single tool

- For Non-insulated open barrel #12 to #22 AWG (.324mm2 to 3.331mm2)
- Provides good and consistent crimp every time
- Dies change quickly and easily with a screwdriver
- Interchangeable dies provide versatility in a single tool

- For 50 Ohm and 75 Ohm cables
- Hex hole sizes: .213 in.(5.41mm), .178 in.(4.52mm), .068 in.(1.73mm) and .042 in. (1.07mm)
- Provides good and consistent crimp every time
- Dies change quickly and easily with a screwdriver
- Interchangeable dies provide versatility in a single tool

- For fully-insulated quick disconnect terminals with thinner wire barrels #10 to #22 AWG (.324mm2 to 5.261mm2)
- Provides good and consistent crimp every time
- Dies change quickly and easily with a screwdriver.
- Interchangeable dies provide versatility in a single tool

- For single or multiple conductor cable up to 1-1/2 inch(44mm) O.D.
- Blade adjusts for jacket thicknesses up to 1/8 inch

The patented PTX Series of Wire Wrapping Tools bring a new level of wire wrapping proficiency to installers, telecom technicians and other users.

This wire wrapping tool has a maximum usage rating of 2,500 cycles/day, will wire wrap 18 to 30 AWG wire and is available in both battery and electric models.

The PTX also features a dual-finger short-throw trigger, a long handle to mitigate pressure on the palm to prevent repetitive stresses and a comfort design based on the recommendations of our certified ergonomist. The housing is rugged yet light in weight and includes additional features including a wrap unwrap switch, a high-powered motor for the heaviest gauges of wire and a permanently attached collet nut. Besides being available in both a battery and electric models, the electric PTX Wire Wrapping tools are available with a unique optional feature known as backforce.*

* Backforce is a spring-loaded internal device that is utilized to help the operator eliminate excess pressure against connections on critical applications. The succeeding turns of wire being wrapped on the terminal forces the wire wrapping bit rearward against a predetermined spring pressure. This assures that every connection on the panel has been wrapped at the same pressure. The backforce wire wrapping feature is recommended for new users/trainees and is best when used on wire gauges 26 to 30 AWG.

- Ergonomic Design - Minimizes Repetitive Stress
- A 20' Long Power cord
- Rugged Construction for Field Usage
- Battery and Electric Powered Versions Available
- Wraps and Unwraps 18 to 30 AWG Wire
- Rated Maximum Usage: 2,500 cycles/day

The patented PTX Series of Wire Wrapping Tools bring a new level of wire wrapping proficiency to installers, telecom technicians and other users.

This wire wrapping tool has a maximum usage rating of 2,500 cycles/day, will wire wrap 18 to 30 AWG wire and is available in both battery and electric models.

The PTX also features a dual-finger short-throw trigger, a long handle to mitigate pressure on the palm to prevent repetitive stresses and a comfort design based on the recommendations of our certified ergonomist. The housing is rugged yet light in weight and includes additional features including a low battery indicator, wrap unwrap switch, a high-powered motor for the heaviest gauges of wire and a permanently attached collet nut. Besides being available in both a battery and electric models, the electric PTX Wire Wrapping Tools are available with a unique optional feature known as backforce.*

* Backforce is a spring-loaded internal device that is utilized to help the operator eliminate excess pressure against connections on critical applications. The succeeding turns of wire being wrapped on the terminal forces the wire wrapping bit rearward against a predetermined spring pressure. This assures that every connection on the panel has been wrapped at the same pressure. The backforce wire wrapping feature is recommended for new users/trainees and is best when used on wire gauges 26 to 30 AWG.

- Ergonomic Design - Minimizes Repetitive Stress
- Rugged Construction for Field Usage
- Battery and Electric Powered Versions Available
- Wraps and Unwraps 18 to 30 AWG Wire
- Rated Maximum Usage: 2,500 cycles/day

- Crimps on fish tape in minutes
- Use with IDEAL S-Class® fiberglass fish tape repair kit
- Connection guaranteed to withstand 500 lbs.
- Box of four

The improved FishTix™ II Cable installation kit is designed to pull large, heavy cable bundles across long areas such as cable trays, suspended tile ceilings and even under raised flooring common in data rooms. Great for data and communications installations, the FishTix 4ft. rod sections are made of a flexible non-conductive tubular material with snap together detent connectors. Snap the rods together to reach your desired length – in cable trays, the length can be infinite! The FishTix rods offer extreme tensile strength capable of handling over 200lbs. of pulling force. /n The standard kit comes with twelve 4ft. rods for a total available length of 48ft. Additional 4ft. sections can be added or multiple kits can be combined to reach longer lengths. The 4ft. rod length allows you to assemble your rods together in confined spaces. The kit also comes with a resilient whisk head that can be used to ride up over beams, ceiling tile grids, joists and existing cable runs. Includes a full nylon carry case for storage with a convertible shoulder/hand strap for easy transport.

  The FishTix II Cable Kit Contains:
- Twelve 4ft. x 7/8" diameter Flexible Tube Sections with Detent Connectors
- Resilient Whisk Head
- Female Bull Nose Head
- Male Bull Nose Head
- A 3/16" Quick Link Attachment Coupler
- Full nylon case with snap buckle closure and shoulder strap

FishTix Replacement Whisk Head

FishTix Nylon Case

Accept no inferior knock-off products - use the original - the Wet Noodle Retriever System. LSDI developed the ball chain and retriever concept to help save installation time. Since its introduction, it has evolved into a “must have” tool for retrofit installation. The Wet Noodle Retrieval System has been updated to now contain three components: a 24" flexible insulated retriever with an ultra strong earth magnet attached at one end; 10ft. of lightweight ball chain with a stop-ring; and an 18" telescoping pocket retriever. This system provides a fast and easy solution to connecting an in-wall entry point to an exit point blindly (without vision tools) to pull wire.

Product Hi-Lite
NEW Larger more Powerful 1/4" magnet has been added to the opposite end of the original 3/16" Neodymium magnet for extra pulling power!

Accept no inferior knock-off products - use the original - the Wet Noodle Retriever System. LSDI developed the ball chain and retriever concept to help save installation time. Since its introduction, it has evolved into a “must have” tool for retrofit installation. The Wet Noodle Retrieval System has been updated to now contain three components: a 24" flexible insulated retriever with an ultra strong earth magnet attached at one end; 10ft. of lightweight ball chain with a stop-ring; and an 18" telescoping pocket retriever. This system provides a fast and easy solution to connecting an in-wall entry point to an exit point blindly (without vision tools) to pull wire.

  Product Hi-Lite
NEW Larger more Powerful 1/4" magnet has been added to the opposite end of the original 3/16" Neodymium magnet for extra pulling power!

Accept no inferior knock-off products - use the original - the Wet Noodle Retriever System. LSDI developed the ball chain and retriever concept to help save installation time. Since its introduction, it has evolved into a “must have” tool for retrofit installation. The Wet Noodle Retrieval System has been updated to now contain three components: a 24" flexible insulated retriever with an ultra strong earth magnet attached at one end; 10ft. of lightweight ball chain with a stop-ring; and an 18" telescoping pocket retriever. This system provides a fast and easy solution to connecting an in-wall entry point to an exit point blindly (without vision tools) to pull wire.

  Product Hi-Lite
NEW Larger more Powerful 1/4" magnet has been added to the opposite end of the original 3/16" Neodymium magnet for extra pulling power!

Introducing the new premium line of BULZ-EYE™ self-feed wood boring bits from IDEAL Industries Inc. BULZ-EYE™ self-feed bits include a number of superior features and benefits that combine to deliver the most outstanding performance of any self-feed bit product available today. The new design features twin cutting edges and precision ground teeth with up to 50% wider cutting surface. These features deliver improved cutting speeds, better balance and control and clean more accurate holes then the leading brands on the market. BULZ-EYE™ self-feed bits are manufactured with the best materials and machinery available to ensure quality, performance and durability. IDEAL is the professional’s choice for self-feed bits.

  Features:
- Wider precision ground teeth for maximum control.
- Robust replaceable lead screw with burr-free threads.
- Twin cutting edges for faster, more balanced drilling and cleaner holes.
- Precision machined shaft eliminates wobble resulting in accurate holes.
- Quick change shank design for fast bit changes & use with pneumatic drills.
- Black oxide coated, heat treated and hardened for improved durability.