Siemon’s single-sided vertical cable management channels provide an economic solution for managing large cable bundles between adjacent racks. They feature an open design with six easily configured dual-hinge managers (additional managers available separately) that enable customized management of patch cords. Cable access holes allow cords to be routed between the front and rear of the channel. Mounting holes within the channel accommodate Siemon’s quarter-turn cable managers (p/n RS-CH) and quarter-turn hook and loop cable managers for further customization of cable routing.

The channels are available in both 76mm (3 in.) and 152mm (6 in.) depths for use with standard 76mm (3 in.) racks or 152mm (6 in.) deep cable management racks such as Siemon’s RS-07. Alternately, the 76mm (3 in.) deep channels can be stacked back to back with the deeper cable management racks to optimize management of cables on both sides of the channel.

  Specifications:
- 76mm (3 in.) x 2.1m (7 ft.)
- vertical cable management
- channel for mounting
- between 76mm (3 in.) deep
- racks (includes hardware)

This Field Breakout Kit is designed to attach to one tube of a loose tube cable. They have either six or twelve 900 µm tubes that hold each of the coated fibers. For each end of the cable, one kit is needed for every tube. For example, part number M9B511 has two tubes with six 62.5/125 fibers each. This cable requires four field breakout kits; two for each end of the cable.

The kit is available in two sizes to accommodate the two different tube sizes which are manufactured by Mohawk. For tubes containing one to six fibers, the diameter is 0.075" (1.9 mm) and for tubes containing seven to twelve fibers, the diameter is 0.110" (2.8 mm).

This Field Breakout Kit is designed to attach to one tube of a loose tube cable. They have either six or twelve 900 µm tubes that hold each of the coated fibers. For each end of the cable, one kit is needed for every tube. For example, part number M9B511 has two tubes with six 62.5/125 fibers each. This cable requires four field breakout kits; two for each end of the cable.

The kit is available in two sizes to accommodate the two different tube sizes which are manufactured by Mohawk. For tubes containing one to six fibers, the diameter is 0.075" (1.9 mm) and for tubes containing seven to twelve fibers, the diameter is 0.110" (2.8 mm).

The Triplett SatAlign is a quick and economical way for the do-it-yourselfer to install or realign a DBS satellite dish. No need to pay for expensive service calls! Just connect the SatAlign between the LNB and any DBS Satellite Receiver and you can precisely align your dish in seconds. The SatAlign, with its built-in signal strength meter, is extremely sensitive with a quick response time making satellite alignment a breeze. The SatAlign works with all brands of Dish Antennas and Satellite Receivers. It will save you hours of installation time and guarantees exact alignment for the best picture quality and maximum rainfade reserve.

Rugged thermometer with 12:1 distance to target ratio

High 12 to 1 distance to target ratio measures smaller surface areas at greater distances

	Product Features:
-	Widest temperature range from -58° to 1400°F (-50 to 760°C)
-	Built-in laser pointer identifies target area
-	Backlighting illuminates display for taking measurements at night
-	Automatic Data Hold

  

	Product Features:
-	Unique, padded suspenders engineered to carry loads comfortably and distribute weight evenly without strain on lower back and hips.
-	Easy Carry Handle design provides for simple adjustments and easy storage without spilling contents. Patent #6,179,185
-	Zippered top flap pouch to prevent spillage of tools when not in use
-	Built-in cordless drill pocket.
-	3” Wide padded comfort belt with double tongue steel roller buckle fits waist sizes 29”– 46”.
-	Tape strap, tool snap and metal hammer holder
	TOOLS NOT INCLUDED WITH TOOL BELT

  

  Product Features
- Consistent, positive tension
- Flush cut-off leaves no projections to damage nearby wires or components
- Rugged, die-cast aluminum construction with comfortable, cushioned grips
- Scrap tail stays in tool until trigger is released

Use with standard and heavy-duty ties

1.25mm universal

2.5mm universal

LC Simplex Duplex adapter

This compact kit contains a special purpose splicer's knife, scissor and leather pouch. The knife features a short 13/4” tough, cutlery-steel blade and a non-slip handle. The scissors are made of high carbon steel with scraper and file on one sides. Both items fit securely in the leather pouch which can be mounted on belts up to 2” wide.

Replacement Bit F-Style Connector

  Product Features:
- High-Carbon Steel Blade Cable Splicing Knife
- Durable Leather Holder

-	Provides protection for cables
-	Packaged on a reel for easy handling and dispensing of product
-	For indoor use only
-	Material: Polyethylene
-	Inside Dia: 0.76"
-	Outside Dia: 0.94"
-	Length: 100'

Don't waste valuable real estate in the back of the rack. IEC Power Cords eliminate space-wasting excess cable slack in rack installations. Available in multiple sizes, these cords can be substituted for standard power cords provided with electronic components. Choose the appropriate length to provide a shorter path from component to power strip, eliminating unnecessary cable loops, and helps prevent system noise from stray AC magnetic fields. Cords feature connector in coordinating colors to allow easy identification during installation and servicing. Sold in packs of four (1 each color: Black, Brown, Gray, and White)